How to Hang Pre-hung Door - Part 6 of 15 - Recycled Metal Removed

Fig.1 The Tools

By Gary Boutin

Supplies and Tools:
Cordless Screwdriver with Phillip bit
Claw Hammer 
Paint scraper

Mr. Victor Longpont hired my services to remove his garage door that had become damaged after a bad rain storm. The door had not been painted for over 30 years, the bottom of the door was completely rusted. 

This post shows the seven steps to recycle the damaged door hardware. 

Step 1: Fig.1 shows the door that has been removed and set on its side.  
Step 2: Fig.2 shows the use of a cordless drill with a Phillip screwdriver bit to remove the latch and door handle from the door.

Fig.2 Door Hardware

Fig.3 Hardware

Step 3: Fig.4 shows the removal of the dead bolt lock assembly. Notice the long metal screw, it's made of brass and so is most of the lock assembly. Use the cordless screwdriver to remove the lock parts.

Fig.4 Strike Plate

Step 4: Fig.5 shows the removal of the metal hinges. On this door there were three sets of metal hinges. Using the cordless screwdriver remove each brass screw and save for later. 
Step 5: Fig.6 shows the removal of the aluminum weatherstripping seal that was around the door. Save the metal for later.

Fig.5 Hinges

Fig.6 Removing aluminum weatherstrip

Step 6: Fig.7 shows all the metal from the damaged door ready for recycling. The aluminum weatherstripping, brass door hardware for the door handle, screws and dead bolt. The metal door sweep and the aluminum threshold plate will be used to make other materials instead of landing in the waste dump.

Fig.7 Recycle Metal

Step 7: Recycling is not a money maker, its hard work to separate each type of metal.  Sometimes what looks like brass is plated metal but recycling metal parts is a good a way to keep our environment cleaner.

How to Hang a Pre-hung Door:

Part 1 of 15 Introduction Why Replace This Garage Door

Part 2 of 15 Removing The Damaged Door

Part 3 of 15 Door Hardware Removed

Part 4 of 15 Door Threshold Removal

Part 5 of 15 Installing Door

Part 6 of 15 Recycled Metal Removed

Part 7 of 15 Caulking Outside Door Edges

Part 8 of 15 New Door Hardware Installed

Part 9 of 15 Caulking Door Screws Holes

Part 10 of 15 Inside Door Mud

Part 11 of 15 Inside Door Taping

Part 12 of 15 Inside Door Painted

Part 13 of 15 Applying Stucco To Door Edge

Part 14 of 15 Exterior Door Molding

Part 15 of 15 Old Door Cut to Trash

Update: DIY Advisor has New blogs check them today:

• Handyman Blog: DIY Advisor
• DIY Advisor Sitemap
• Food Blog: From Kiwis To Pistachios!
• Food Blog Sitemap
• Tool Blog: DIY Advisor Toolbox
• Tool Blog Sitemap
• Artwork Blog: Light in Dark Artwork
• Artwork Blog Sitemap
• Class-A Tests: DIY Class-A Drivers License Tests
• Class-A Tests Sitemap: Class-A Sitemap
• DIY Poem: DIY Poem Meter Blog
• DIY Poem Sitemap: DIY Sitemap

• Cookie Alert: European Union laws requires that you know that this blog uses cookies. If you are concerned about this please click here to see how Google uses this information.

Note: The DIY Advisor assumes no liability for omissions, errors or the outcome of any jobs. The reader must always exercise reasonable caution, follow current codes and regulations that may apply, and is urged to consult with a licensed contractor if in doubt about any steps on these posts. All names were changed to protect client's privacy. DIY Advisor. Reproduction of site content including photos without permission prohibited. All rights reserved. © Copyright 2011-