California Automobile Registration Sticker Protection

Fig.1 Toyota Trademark

By Gary Boutin


Tools and Supplies:
License Plate
Phillip Screwdriver
Razor knife or razor blades
Registration Sticker

California registration sticker give the driver the right to drive the roads. These metal foil stickers are expensive and need protecting. In California you can not place your driver license inside a protective case. The case could prevent police officers from reading the license plate and registration stickers.

This post shows the twelve steps to protecting your registration stickers. This should work for any state that uses registration foil sticker.

Step 1: Fig.1 above right shows the Toyota Trademark.
Step 2: Fig.2 below shows the peeling of older registration foil stickers.

Fig.2 Peeling registration stickers

Step 3: Fig.3 shows below the years the California foil sticker was removed intact.

Fig.3 Intact Foil

Step 4: Fig.4 shows below is the California foil stickers that will need protecting.  

Fig.4 Need to Protect This One

Step 5: Fig.5 shows the California Driver Motor Vehicle send with the updated foil sticker a diagram of were to place the sticker.

Fig.5 DMV Foil Location

Step 6: Fig.6 through fig.8 shows the application of the new California registration stickers.

Fig.6 Installing

Fig.7 Pushing sticker flat

Fig.8 Foil is installed

Step 7: To protect the California or any other state the first tool that will be needed is a razor blade (fig.9). If your interested there are two post that deal with installing razor blades. Fig.10 shows the Glass Scraper - Part 1 of 2 - Large Glass Scrapers Installation. If this is to large to work with see the following post. Fig.11 shows the Glass Scraper - Part 2 of 2 - Mini Glass Scrapers

Fig.9 Standard razor blade

Fig.10 Paint scraper

Fig.11 Mini Scraper

Step 8: Now place the foil sticker on the license plate. Use a razor knife, razor blade or a paint scraper to cut the lines into the registration foil. Fig.12 shows diagonal lines to the left that shows the razor cuts into the foil sticker. Fig.13 shows the other side needs to be done too.

Fig.12 Razor cuts diagonally

Fig.13

Step 9: Why? The idea is to make it difficult for a thief to take your entire tag off your vehicle.
Step 10: Fig.14 shows to paint your free license plate cover. Use inexpensive flat or semi-gloss paint to paint the plastic paint.

Fig.14 Flat spray paint

Step 11: Fig.15 shows the plate has been painted.

Fig.15 plate painted

Step 12: Return the metal screws back into the license plate cover. Fig.16 shows a Phillip Screwdriver that will install the plate back onto the vehicle. Fig.17 plate back onto the vehicle. Fig.18 shows the job is done.

Fig.16 Metal screws into plate

Fig.17 Phillip Screwdriver

Fig.18 Job done.

• Handyman Blog: DIY Advisor
• Food Blog: From Kiwis To Pistachios!
• Artwork Blog: Light in Dark Artwork
• Artwork Blog Sitemap
• Class-A Tests: DIY Class-A Drivers License Tests

• Cookie Alert: European Union laws requires that you know that this blog uses cookies. If you are concerned about this please click here to see how Google uses this information.

Note: The DIY Advisor assumes no liability for omissions, errors or the outcome of any jobs. The reader must always exercise reasonable caution, follow current codes and regulations that may apply, and is urged to consult with a licensed contractor if in doubt about any steps on these posts. All names were changed to protect client's privacy. DIY Advisor. Reproduction of site content including photos without permission prohibited. All rights reserved. © Copyright 2011-

How to Paint Brown Living Room - Part 1 of 7 - Taping the Living Room

Fig.1

By Gary Boutin

Supplies and Tools:
Cloth duct tape
Mud pan (red)
Paper tape
Scissors 
Razor knife 
Tarp (plastic)
Tarp painter's cloth




Tyler Zowat lives in Perris, California. He had a new patio installed late last summer and the carpenter accidentally cut a pipe that flooded the bathroom. A local plumber repaired the job but not the drywall. These post show how the job was handle and the walls painted. He purchased all his paint from The Home Depot.

This post shows the four steps on how to tape the room for repair.

Step 1: Fig.1 shows what the local plumber left for Mr. Zowat. Fig.2 shows some of the tools needed to repair this wall job. 

Fig.2

Step 2: Fig.3 through fig.5 shows the areas that was taped with masking tape.

Fig.3

Fig.4

Fig.5

Step 3: Fig.6 through fig.8 shows the taping process.

Fig.6

Fig.7

Fig.8

Step 4: Fig.9 shows the ceiling being tape with painter's tape to prevent the ceiling to be painted.

Fig.9

How To Paint Brown Living Room:

• Part 1 of 7 - Taping the Living Room
• Part 2 of 7 - Repair Wall
• Part 3 of 7 - Vacuum and Texture Clean Up
• Part 4 of 7 - Texture and Clean Up
• Part 5 of 7 - Cut Two Walls
• Part 6 of 7 - Roll Walls
• Part 7 of 7 - Living Room Finished

Update: DIY Advisor has New blogs check them today:

• Handyman Blog: DIY Advisor
• DIY Advisor Sitemap
• Food Blog: From Kiwis To Pistachios
• Food Blog Sitemap
• Tool Blog: DIY Advisor Toolbox
• Tool Blog Sitemap
• Artwork Blog: Light in Dark Artwork
• Artwork Blog Sitemap
• Class-A Tests: DIY Class-A Drivers License Tests
• Class-A Tests Sitemap: Class-A Sitemap
• DIY Poem: DIY Poem Meter Blog
• DIY Poem Sitemap: DIY Poem Sitemap

• Cookie Alert: European Union laws requires that you know that this blog uses cookies. If you are concerned about this please click here to see how Google uses this information.

Note: The DIY Advisor assumes no liability for omissions, errors or the outcome of any jobs. The reader must always exercise reasonable caution, follow current codes and regulations that may apply, and is urged to consult with a licensed contractor if in doubt about any steps on these posts. All names were changed to protect client's privacy. DIY Advisor. Reproduction of site content including photos without permission prohibited. All rights reserved. © Copyright 2011-