Showing posts with label Titebond glue. Show all posts
Showing posts with label Titebond glue. Show all posts

Thursday, January 8, 2015

How to Make Backyard Wood Blind to Cover a Hole in Block Fence

Fig.1 The blind
By Gary Boutin 

Supplies and Tools:
1x6x8 redwood Tongue and Groove (2)
2x2x8 redwood lattice (2)
Clamps 
Compound saw or hand saw 
Deck screws 1 1/4 in.
Lattice beige vinyl cap molding 
                      3/4 in. x 1 in. x 4 ft
Tapcon polymer plated steel hex-washer-head indoor/outdoor 
                  concrete anchors 1/4 in. x 2-3/4 in.
Titebond glue 
Wood drill bit
Wood glue

Jim came to The Home Depot to place a wooden shutter from his backyard block wall. Some time ago he had a hole made in his block wall so he could see the valley from his home. Now the green valleys are filled with new homes. He came to the Anaheim Super Store - Lumber/Building Materials area for information and wanted information on redwood screen.

This post shows the seven steps to assembling block wall blind.

Step 1: Arrive at your nearest The Home Depot and talk to an associate.  If your project involves working with wood ask for the location of Lumber/Building Materials.
Step 2: Fig.1 shows a picture that Jim brought to me to explain the problem. The brown area is the area of concern. The Home Depot carries Douglas Fir tongue and groove will be used across the expanse of the missing block.
Step 3: Fig.2 shows that Jim decided to purchase 1x6x8 redwood tongue and groove. He had both boards cut in half by a lumber associate. Below the wood is being cut to size.
Fig.2 Cutting the planks
Step 4: Now Jim wanted an easy but good looking wood edge to lay on the brick wall. I showed him the mill works area but none fitted correctly against the Tongue and Groove planks. I brought him to the garden area where the 2x2 plastic channel were being stored. 
Step 5: Fig.3 shows we decided on using beige vinyl cap molding. The planks once glued would be surrounded by the molding. It worked perfectly except the sides of the wood screen. Another molding was cut to accommodate the sides of the wood screen.
Fig.3 Laying all the planks 
and cap molding on the floor
Step 6: Fig.4 shows the final assembly to show Jim how to assemble the project.

Fig.4 Final check
Step 7: Blind instructions:
  1. The glue to use on the edges of the tongue and groove boards, make sure the boards are flat and the ends even. Each board is 5-1/2 wide and 4-foot long for a total 2-boards totaling 11 in. long.
  2. Use wood clamps to clamp each end of the boards.
  3. When the board are together cut off the groove side of the board. Removing the groove will give the board a larger flat area.
  4. After the boards are glued together, place the top and bottom cap on each side.
  5. Drill three holes in each cap molding approximately 4-inch on each end and 24 in. the middle hole.
  6. Fig.5 shows that the insertion of three deck screws into the plastic cap and into the tongue and grove boards and two more on each end.
  7. Do this on both horizontal side.
  8. Now insert the deck screws on the lateral side.
  9. Now pick up the entire unit and place it on top of the cement wall. To secure the panel to the brick wall drill into the wood cap first and another hole into the cement. Using Tapcon polymer plated steel hex-washer-head indoor/outdoor concrete anchors 1/4 in. x 2-3/4 in. This is the very best anchoring system. For more information click on Tapcon above.
Fig.5 Deck screw locations
Jim never came by to show off his handiwork. So I am assuming the blind worked and he no longer had to stare at the new development that was happening near his home.  


Update: DIY Advisor has New blogs check them today:
  • Cookie Alert: European Union laws requires that you know that this blog uses cookies. If you are concerned about this please click here to see how Google uses this information.

Note: The DIY Advisor assumes no liability for omissions, errors or the outcome of any jobs. The reader must always exercise reasonable caution, follow current codes and regulations that may apply, and is urged to consult with a licensed contractor if in doubt about any steps on these posts. All names were changed to protect client's privacy. DIY Advisor. Reproduction of site content including photos without permission prohibited. All rights reserved.© Copyright 2011-
 

Posted by at No comments:
Labels: , , , , , , , , , , ,

Monday, November 17, 2014

How to Make Redwood Raised Garden Beds


Fig.1 The plan
By Gary Boutin
Assembled by Jag

Supplies and Tools:
Claw hammer  
Cordless drill
Chip brush; one time use
Copper-Green Wood Preservative Spray
Leather work gloves  
Star Flat Head Wood Deck Screws #10 - 2-1/2 in. (Torx bit included)
Measurement tape
Miter box
Pressure Treated Lumber HF Brown Stain 2 inch x 6 inch x 8 feet (3)
Titebond Original Wood Glue, 16 fluid ounces

Jag stopped by his local The Home Depot for a special raised garden bed that he wanted to make for his wife. He came to the Anaheim Super Store - Lumber/Building Materials area for information and lumber cuts for his project. He needed to understand the difference between Treated Wood and Douglas Fir dimension lumber. 

This post shows the ten steps to assembling a special raised garden bed. 

Step 1: Arrive at your nearest The Home Depot and talk to an associate. If your project involves working with wood, ask for the location of Lumber/Building Materials.
Step 2: Explain the lumber associate about your project. For this project, fig.1 shows that Jag had his plans in his head and together we put the plans on paper.
Step 3: He looked at several thicknesses of lumber to help him decide which wood would last longer. Jag also was inquisitive about what type of metal screws to use on his project. We discussed the hardware and decided to purchase (Fig.2) DeckMate Star Flat-Head Wood Deck Screws #10 2-1/2 inch.  
Fig.2 DeckMate star flat-head 
wood deck screws
Step 4: We decided that the treated 2x6 lumber would be perfect against rot and last a long time in this dry California climate. Pressure-Treated Hem-Fir Lumber is for above ground use and is treated with Copper azole. This lumber has been stained Brown and is paintable. The Home Depot provides a Material Safety Data Sheet for treated lumber.
Step 5: As the raised garden is being assembled, the cut portion of the treated lumber will need to be painted with a Copper-Green Wood Preservative. This preservative protects the wood against the weather and wood eating insects. The Home Depot also provides a Material Safety Data Sheet for your review. 
Step 6: Floor assembly: Fig.3 shows that by placing the lumber on the floor, Jag saw how to secure the corner with two 2x6 lumber and where to drill the wood deck screws into the corner braces.
Fig.3 The assembly #1
Step 7: Floor assembly: First layer. Fig.4 shows that placing the first row on the floor showed him how to assemble the sides of the garden bed.
Fig.4 The assembly #2
Step 8: Floor assembly: First and second layer: Fig.5 shows that the wood was placed on top of each side showing Jag how to build up the walls.
Fig.5 Wood stacked second layer
Step 9: Fig.6 shows the 2x6x4 stacked on The Home Depot lumber cart. Fig.7 and fig.8 shows that each piece was marked to help Jag in the assembly. Fig.9 shows the wood cuts of treated lumber are ready to make his raised garden.
Fig.6 stacked ready to assemble 2x6x4
Fig.7 Long pieces
Fig.8 Short pieces

Fig.9 The project
Step 10: Before the project was finished, Jag had to cut the top piece of the project into 45° degree cut using a Miter Box. After the cuts the top pieces were applied with a Cordless Screwdriver driving in the deck screws into the walls. Fig.10 through fig.12 shows different views of the finished raised garden. All that needs to be done is planting the flowers for Jag's wife. 
Fig.10 Side view finished product
Fig.11 Top view finished product
Fig.12 Job finished finished product
Jag's e-mail note: Thanks you so much for your help today at Home Depot. Attached are the pictures of finished product. It came out really good, Jag. Fig. 10 through fig.12 are the three pictures sent by Jag for this post. 



Update: DIY Advisor has New blogs check them today:
  • Cookie Alert: European Union laws requires that you know that this blog uses cookies. If you are concerned about this please click here to see how Google uses this information.

Note: The DIY Advisor assumes no liability for omissions, errors or the outcome of any jobs. The reader must always exercise reasonable caution, follow current codes and regulations that may apply, and is urged to consult with a licensed contractor if in doubt about any steps on these posts. All names were changed to protect client's privacy. DIY Advisor. Reproduction of site content including photos without permission prohibited. All rights reserved. © Copyright 2011-

Posted by at No comments:
Labels: , , , , , , ,
Subscribe to: Posts (Atom)