How to Repair Maple Wooden Suit Hanger

Fig.1 360 degree swivel rod hook
hanger Description

By Gary Boutin

Tools and supplies
Broken wood hanger
Glue (wood)
Rubber bands Large

Its so easy when our personal things break down like this Maple suit hanger to just throw it away and purchase another new suit hanger. This maple hanger has been doing its duty of holding my work suits for over twenty years and it seemed that repairing the damaged hanger was better choice than spending six dollars to acquire a new hanger. 

This post shows the five steps to saving a Maple wooden suit hanger.

The top of the hanger has a chrome 360-degree swivel rod hook. A coat hanger is a wood device in the shape of human shoulders designed to aid the hanging of a coat, jacket, sweater, that prevents wrinkles. The wooden hanger resembles a flat piece of wood cut into a boomerang-like shape, and with the edges sanded down to prevent damage to the clothing. The wooden bar locks the trousers between a metal wire. Most quality wood hangers are using wood grown in the United States Of America: Bamboo, Beech wood, Birch, Cedar, Red Cedar, Cherry, Maple, Mahogany, and Walnut. Quality hanger also use a high-gloss finish, brown flocking and brass hardware while their counterparts use satin finish, black flocking and chrome hardware.

Fig.2 Pants clip

Step 1: Fig.1 shows the parts description of a wood hanger. Fig.2 shows the metal clamp which pulled out from the top part of the shoulders wooden frame.
Step 2: Fig.3 and fig.4 shows the hanger clamp is in need of repair. Fig.4 shows a metal wire was  roughed up so the wood glue would adhere to the shoulder wood frame.

Fig.3 Hole for pant clip

Fig.4 Rough up pant clip

Step 3: Fig.5 through fig.7 shows the application of glue on the metal clamp and the wooden part of the hanger.

Fig.5 Plastic protect
counter top

Fig.6 Titebond 
wood glue

Fig.7 Apply the 
lue liberally

Step 4: Fig.8 through fig.10 shows the clamp wire was being pressed into the wood frame. Titebond wood glue was the adhesive used to glue the clamp to the shoulder wood frame. 

Fig.8 Push in 
metal pin

Fig.9 Remove 
excess wood glue

Fig.10 Use rubber
bands if needed

Step 5: Fig.11 and fig.12 shows the wood hanger has been repaired and is holding a pair or slacks.   

Fig.11 Repair worked

Fig.12 Job finished

Note: Cedar is a natural insect repellent and inhibit mildew smells. A wooden hanger can be purchased in bulk between 74-cents to three dollars. 

Wooden Suit Hanger Internet Links:
How to buy click here. Wooden hangers click here or here. How to make a wooden hanger, click here.

Update: DIY Advisor has New blogs check them today:

• Handyman Blog: DIY Advisor
• DIY Advisor Sitemap
• Food Blog: From Kiwis To Pistachios
• Food Blog Sitemap
• Tool Blog: DIY Advisor Toolbox
• Tool Blog Sitemap
• Artwork Blog: Light in Dark Artwork
• Artwork Blog Sitemap
• Class-A Tests: DIY Class-A Drivers License Tests
• Class-A Tests Sitemap: Class-A Sitemap
• DIY Poem: DIY Poem Meter Blog
• DIY Poem Sitemap: DIY Poem Sitemap

• Cookie Alert: European Union laws requires that you know that this blog uses cookies. If you are concerned about this please click here to see how Google uses this information.

Note: The DIY Advisor assumes no liability for omissions, errors or the outcome of any jobs. The reader must always exercise reasonable caution, follow current codes and regulations that may apply, and is urged to consult with a licensed contractor if in doubt about any steps on these posts. All names were changed to protect client's privacy. DIY Advisor. Reproduction of site content including photos without permission prohibited. All rights reserved. © Copyright 2011-

How to Repair a Wood Dresser Drawer Guide

Fig.1 The tools

By Gary Boutin
 
Supplies and Tools: 
3/4 X 3/4 hard Birch wood
1x2x4 Douglas Fir 
Chisel wood 1-inch
Cordless circular saw Makita
Cordless 9-volt batteries Makita 
Cordless screwdriver and Phillip Bit
Drill Electric
Electrical cords 
Glue acid brush

Electrical screwdriver

Spade bits 1/2 inch countersink
Spring clamps - large and medium
Pan head screws
Washers metal chrome
Wood bench (2)
Wood glue
Wood pencil #2
Wood planner - electric

James Tu called to repair an old wood dresser that was given to him when he became a United States citizen. He knew the dresser did not have any monetary value but he wanted it repaired. I advised him to go to a furniture repair company but he wanted to repair it today if possible. This is a temporary repair of a wooden dresser.

This post shows the fourteen steps on how to make a wood drawer guide for an antique dresser.

Step 1: Fig.1 shows the tools needed for this repair. All tools listed above. 
Step 2: Fig.2 and fig.3 shows the old drawer guide made of wood from an antique wood dresser. It appeared to be a T-shaped guide and the side are not square for the metal slide.

Fig.2 Damaged wood 
drawer guide

Fig.3 Slide worn

Step 3: Fig.4 shows the old drawer guide was worn off by the drawer metal slide. The metal slide slid over the wood T-guide to open and close the drawer. According to Mr. Tu the metal slide was installed a few years earlier by another handyman.

Fig.4 Drawer splintered

Step 4: Fig.5 shows the underneath the middle drawer was a metal slide and the entrance of the drawer is at the bottom of picture. Fig.6 shows the end of the drawer were the metal piece is supported by the back drawer piece.

Fig.5 Drawer slide

Fig.6 Drawer other end

Step 5: Fig.7 shows the steps of how the wood drawer slide was made. By placing two pieces together the wood slide was made.

Fig.7 Making the slide

Step 6: Fig.8 shows an electric wood planer that will be used to removed wood to make the wood drawer slide.

Fig.8 Wood planner

Step 7: Fig.9 shows a Makita radial saw cutting the 3/4 by 3/4 hardwood piece. This piece will fit inside the metal slide. Fig.10 and fig.11 shows the Makita radial Saw cutting each piece of the drawer slide to size. The wood drawer guide is made from two pieces of wood.

Fig.9 Sizing the rail

Fig.10 Cutting bottom rail

Fig.11 Cutting drawer top slide

Step 8: Fig.12 shows the assembled drawer guide without the notch assembly.

Fig.12 Drawer guide

Step 9: Fig.13 shows a notch (cut out) had to on the guide so the attachment could be placed inside the dresser. 

Fig.13 Guide notch

Step 10: Fig.14 shows the wood glue was placed on the wood guide with spring clamps were used to hold the pieces together.

Fig.14 Spring clamps

Step 11: Fig.15 through fig.20 shows the process of creating the hole for the pan head screw into the wood guide that will allow the drawer into the cabinet.

1. Fig.15 shows the hole is drilled into the guide.
2. Fig.16 shows the hole is countersunk to fit the edges of the pan head screw.
3. Fig.17 shows a 1/2 inch spade bits countersink is started.
   
4. Fig.18 shows the hole is not deep enough.
5. Fig.19 show that the guide is clamped in place using spring clamps. 
6. Fig.20 shows the guide is notched and the hole is ready to used.

Fig.15 Cordless drill 
create screw hole

Fig.16 After the hole 
countersink the screw

Fig.17 1/2 inch
 countersink

Fig.18 Not deep enough

Fig.19 Spring clamps 
hold guide

Fig.20 Ready to use

Step 12: Once the guide was glues together a pan head screw was used to give the wood guide for strength. Fig.21 and fig.23 shows the transition of the pan head screw being attached to the wood guide.

Fig.21 Insert screw

Fig.22 Place screw

Fig.23 Remove 
and re-insert

Step 13: Fig.24 shows the testing the new drawer guide with the metal drawer slide. It fits but its too long like in fig.25. Fig.26 shows the finished wood guide being inserted into the metal glide.

Fig.24 Drawer slide and Wood guide

Fig.25 T-guide fits but its too long

Fig.26 Finished guide

Step 14: Fig.27 shows this is the new wood drawer guide inserted back into the dresser. Fig.28 shows the dresser now repaired.

Fig.27 Inserted 
into cabinet

Fig.28 Dresser repaired

Update: DIY Advisor has New blogs check them today:

• Handyman Blog: DIY Advisor
• DIY Advisor Sitemap
• Food Blog: From Kiwis To Pistachios!
• Food Blog Sitemap
• Tool Blog: DIY Advisor Toolbox
• Tool Blog Sitemap
• Artwork Blog: Light in Dark Artwork
• Artwork Blog Sitemap
• Class-A Tests: DIY Class-A Drivers License Tests
• Class-A Tests Sitemap: Class-A Sitemap
• DIY Poem: DIY Poem Meter Blog
• DIY Poem Sitemap: DIY Sitemap!

• Cookie Alert: European Union laws requires that you know that this blog uses cookies. If you are concerned about this please click here to see how Google uses this information.

Note: The DIY Advisor assumes no liability for omissions, errors or the outcome of any jobs. The reader must always exercise reasonable caution, follow current codes and regulations that may apply, and is urged to consult with a licensed contractor if in doubt about any steps on these posts. All names were changed to protect client's privacy. DIY Advisor. Reproduction of site content including photos without permission prohibited. All rights reserved. © Copyright 2011-